What are the Basic Processes for Manufacturing Circuit Board?

      Circuit Board process technology is developing very fast, and each different PCB manufacturer uses different process technologies. Different types and requirements of circuit board also need adopt different manufacturing techniques, but in these different techniques, there are many essential basic processes that are similar. So, what are the essential processes when manufacturing circuit board?


1. Basemap Film Manufacturing Board

The basemap film determines the pattern to be configured when circuit board is manufactured. Moreover, no matter which technical method is adopted in the production process of the circuit board, it is necessary to use a base film film which meets the quality requirements. Therefore, the basemap film is an important tool when manufacturing circuit boards, and it is also the first step in manufacturing techniques.

 

 

2. Pattern Transferring

After manufacturing the baseboard, transfer the designed circuit diagram to the copper-clad laminate. This process is called pattern transfer. If the method of screen printing is used for pattern transfer when the circuit board is manufactured, firstly, a layer of paint film or adhesive film should be coated and adhered on the screen, and then the printed circuit diagram can be made into a hollow pattern as required. When printing, just position the copper-clad laminate on the bottom board, so that the silkscreen and the copper-clad laminate directly contact and print, and then dry and repair the after the print.

 

 

3. Chemical Etching

During circuit board manufacturing, etching is often referred to as rotten board. It uses chemical methods to remove unwanted copper foil on the board, leaving patterns such as pads, printed wires and symbols. In order to ensure the quality, pre-etching should be performed before etching, that is, immerse the copper-clad laminate printed with the resist pattern in the etching solution, and then dip the etching solution with a pen or a writing brush, and then brush the board horizontally and vertically to check the pattern transfer quality.

 

 

The above are the essential basic processes of circuit boards manufacturing. HOYOGO circuit board manufacturing company will take every manufacturing step seriously to ensure the quality of the circuit board. Whenever etching is completed, hole metallization and metal coating are required, and then effective soldering is performed to complete the entire circuit board manufacturing process.

评论

发表评论

此博客中的热门博文

What are the Advantages and Disadvantages of the OSP Technology

图片
     With the continuous development of the electronics industry, there are more and more PCB surface treatment technologies, and each technology has its own merits. OSP is a commonly used surface treatment technology process, what are its advantages and disadvantages?       Compared with other surface treatment technologies, OSP is somewhat different.  It uses a chemical method to produce an organic film on the clean bare copper surface, which acts as a barrier between the copper and the air.   OSP is organic, not  metallic,   and its cost is lower than most surface treatment technologies.     Advantages: With this organic film, it can resist the attack of moisture in the air without being oxidized before welding,  can withstand the test of high temperature, maintain good activity, and has a good tinning ability.  This layer of organic film will not cause damage to the sheet material. It can be easily removed by the solder resist during soldering. It can solder the copper wire and the
阅读全文

What PCBA Problems Can AOI Inspect

图片
        With the development of science and technology, the volume of PCBA is getting smaller and more precise, and some defects in processing cannot be distinguished with the naked eye, so AOI has appeared.  So what PCBA problems can AOI inspect?   The working principle of AOI is to first collect and input parameters such as images, component positions, solder joints and other parameters of the good-quality board.   During the inspection, the instrument automatically scans the circuit board and automatically captures the image, and then compares the collected data with the pre-entered parameters to determine whether the characteristics of solder joints, components and other aspects are consistent. If the data is inconsistent, the d efect  will be flagged through the display for maintenance personnel to repair.     AOI is mainly used to inspect solder paste printing, component placement and soldering. For example: too much or too little solder paste,   solder paste printing offset;  co
阅读全文

The Role of Shield Cover in PCB Design

图片
  SHENZHEN HOYOGO ELECTRONIC TECHNOLOGY CO., LTD. specializes in providing overall PCBA electronics manufacturing services, and can also provide customers with a full range of value-added services: including SMT assembly, PCB program development, schematic design, PCB layout and routing, Bom list matching, component procurement and other services. Do you know the role of shield cover in PCB design? What is a Shield Cover? The shield cover is an alloy metal cover, which is a vital component to reduce the radiation of the display. It is used in MID or VR products, which can effectively reduce the mutual interference between modules. It is common in the isolation between the main control function module and the power module and the Wifi module. The  P urpose of  S hield  Cover   C lip Generally, there are products that use wireless communication, and shield frames are usually designed on the circuit board to isolate electromagnetic interference (EMI). However, to make the shield frame fun
阅读全文