Why do PCB need Vias Plugged with Resin

       Via plugged with resin can solve the problems that green oil plug holes can't solve, but the characteristics of the resin used in this process need to overcome many difficulties in production in order to obtain good quality resin products. So why do PCB vias plugged with resin?

 

Traditional BGA may make vias between pads to the back for routing. If the BGA is too dense, it is impossible to route from the vias to the back, but you can drill directly from the pad to other layers for routing, then plug the vias with resin, and plate copper to form the pad. If only holes are made on the pads without resin plug holes, it will easily lead to short circuit on the back and virtual soldering on the front.

 

 

The PCB vias plugged with resin process includes drilling, electroplating, plugging, baking, and grinding. The holes are drilled and copper plated, then the resin is plugged and baked, and the resin is ground flat by grinding. Because the ground resin does not contain copper, an additional layer of copper is required to become a pad. These processes are all done before the original PCB drilling process, that is, the holes of the fortification holes are processed first, and then the other holes are drilled.

 

 

So what should be paid attention to in the resin plug hole? If the plug hole is not plugged properly, it will cause air bubbles in the hole. Because air bubbles easily absorb moisture, the PCB board may burst when passing through the tin furnace. In the process of PCB vias plugged with  resign, if there are air bubbles in the holes, the air bubbles will squeeze out the resin during the baking process, causing unevenness. At this time, defective products can be detected. The main reason for PCB explosion is moisture, so the resin plug via PCB that has just been received from the factory should be used in time, or be baked before use.

 

 

HoYoGo is an international, professional and reliable PCB manufacturer with our own production capacity, we are able to provide you with one-stop service for small, medium to high volume production. HoYoGo can provide HDI board, gold finger board, Hard gold, FPC, R-F, metal base, quick tun and PCBA.

评论

发表评论

此博客中的热门博文

What are the Advantages and Disadvantages of the OSP Technology

图片
     With the continuous development of the electronics industry, there are more and more PCB surface treatment technologies, and each technology has its own merits. OSP is a commonly used surface treatment technology process, what are its advantages and disadvantages?       Compared with other surface treatment technologies, OSP is somewhat different.  It uses a chemical method to produce an organic film on the clean bare copper surface, which acts as a barrier between the copper and the air.   OSP is organic, not  metallic,   and its cost is lower than most surface treatment technologies.     Advantages: With this organic film, it can resist the attack of moisture in the air without being oxidized before welding,  can withstand the test of high temperature, maintain good activity, and has a good tinning ability.  This layer of organic film will not cause damage to the sheet material. It can be easily removed by the solder resist during soldering. It can solder the copper wire and the
阅读全文

What PCBA Problems Can AOI Inspect

图片
        With the development of science and technology, the volume of PCBA is getting smaller and more precise, and some defects in processing cannot be distinguished with the naked eye, so AOI has appeared.  So what PCBA problems can AOI inspect?   The working principle of AOI is to first collect and input parameters such as images, component positions, solder joints and other parameters of the good-quality board.   During the inspection, the instrument automatically scans the circuit board and automatically captures the image, and then compares the collected data with the pre-entered parameters to determine whether the characteristics of solder joints, components and other aspects are consistent. If the data is inconsistent, the d efect  will be flagged through the display for maintenance personnel to repair.     AOI is mainly used to inspect solder paste printing, component placement and soldering. For example: too much or too little solder paste,   solder paste printing offset;  co
阅读全文

The Role of Shield Cover in PCB Design

图片
  SHENZHEN HOYOGO ELECTRONIC TECHNOLOGY CO., LTD. specializes in providing overall PCBA electronics manufacturing services, and can also provide customers with a full range of value-added services: including SMT assembly, PCB program development, schematic design, PCB layout and routing, Bom list matching, component procurement and other services. Do you know the role of shield cover in PCB design? What is a Shield Cover? The shield cover is an alloy metal cover, which is a vital component to reduce the radiation of the display. It is used in MID or VR products, which can effectively reduce the mutual interference between modules. It is common in the isolation between the main control function module and the power module and the Wifi module. The  P urpose of  S hield  Cover   C lip Generally, there are products that use wireless communication, and shield frames are usually designed on the circuit board to isolate electromagnetic interference (EMI). However, to make the shield frame fun
阅读全文