Application of Ceramic PCB in 3 Fields

Ceramic PCB is made by bonding the copper foil and the ceramic substrate together in a high temperature environment. Its bonding force is strong, the copper foil will not fall off, and the reliability is high. Its performance is stable under the environment of high temperature and high humidity, so it is widely used in three fields.

 

 

 

1. Automotive electronics industry

Ceramic PCB is very important in improving the overall quality of automotive sensors. The material of the sensor chip is generally silicon, and the thermal expansion coefficient of ceramics and the chip are close, and will not cause too much deformation when the temperature difference changes drastically to cause the circuit to be unsoldered. When a car is running, the internal parts of the car body are in a very harsh environment, and they are often exposed to high temperature and strong corrosion. Ceramic PCB uses inorganic non-conductive ceramic as the base material, and the metal is in direct contact with the ceramic, which has strong corrosion resistance.

 

 

2. Communications industry

We are surrounded by all kinds of communication information every day, such as radio, mobile phone, radio communication, navigation, etc., constantly filling our world, and they have become a part of our lives. The reason why they can serve us normally is not only because of modern and advanced network technology, but also because of the important media-antenna.

Antennas are versatile and may be used in a wide variety of environments.The general PCB cannot match its basic performance, and the current high matching degree with it is a ceramic PCB. The antenna in use can generate dangerously high voltages. However, the ceramic PCB has good insulation, which can effectively guarantee personal safety and equipment protection. It can also carry out high-density assembly, so as to realize the short, small, light and thin communication equipment.

 

 

3. Aerospace

In the air or in space, the aircraft must withstand ubiquitous forces. The magnitude of the force determines whether the aircraft can operate normally, so a lot of pressure sensors are needed to detect these forces. For example, a series of force sensors such as the engine's intake pressure sensor, exhaust pressure sensor, cabin pressure sensor, and external pressure sensor. Ceramic PCB is better than the general PCB, its stability, reliability, high precision, resistance to cosmic rays, corrosion resistance, etc. fully meet the needs of pressure sensors.

 

 

The above is the application of ceramic PCB in three major areas. Ceramic PCB is the direction of market demand, and it is constantly advancing the development of science and technology, and its technology is becoming more and more mature. The future is far more than that, and will be applied to more fields. SHENZHEN HOYOGO ELECTRONIC TECHNOLOGY CO., LTD. is a international, professional and reliable ceramic PCB manufacturer. With our mature technology and high-quality services, we are highly praised and good comments from customers.

评论

发表评论

此博客中的热门博文

What are the Advantages and Disadvantages of the OSP Technology

图片
     With the continuous development of the electronics industry, there are more and more PCB surface treatment technologies, and each technology has its own merits. OSP is a commonly used surface treatment technology process, what are its advantages and disadvantages?       Compared with other surface treatment technologies, OSP is somewhat different.  It uses a chemical method to produce an organic film on the clean bare copper surface, which acts as a barrier between the copper and the air.   OSP is organic, not  metallic,   and its cost is lower than most surface treatment technologies.     Advantages: With this organic film, it can resist the attack of moisture in the air without being oxidized before welding,  can withstand the test of high temperature, maintain good activity, and has a good tinning ability.  This layer of organic film will not cause damage to the sheet material. It can be easily removed by the solder resist during soldering. It can solder the copper wire and the
阅读全文

What PCBA Problems Can AOI Inspect

图片
        With the development of science and technology, the volume of PCBA is getting smaller and more precise, and some defects in processing cannot be distinguished with the naked eye, so AOI has appeared.  So what PCBA problems can AOI inspect?   The working principle of AOI is to first collect and input parameters such as images, component positions, solder joints and other parameters of the good-quality board.   During the inspection, the instrument automatically scans the circuit board and automatically captures the image, and then compares the collected data with the pre-entered parameters to determine whether the characteristics of solder joints, components and other aspects are consistent. If the data is inconsistent, the d efect  will be flagged through the display for maintenance personnel to repair.     AOI is mainly used to inspect solder paste printing, component placement and soldering. For example: too much or too little solder paste,   solder paste printing offset;  co
阅读全文

The Role of Shield Cover in PCB Design

图片
  SHENZHEN HOYOGO ELECTRONIC TECHNOLOGY CO., LTD. specializes in providing overall PCBA electronics manufacturing services, and can also provide customers with a full range of value-added services: including SMT assembly, PCB program development, schematic design, PCB layout and routing, Bom list matching, component procurement and other services. Do you know the role of shield cover in PCB design? What is a Shield Cover? The shield cover is an alloy metal cover, which is a vital component to reduce the radiation of the display. It is used in MID or VR products, which can effectively reduce the mutual interference between modules. It is common in the isolation between the main control function module and the power module and the Wifi module. The  P urpose of  S hield  Cover   C lip Generally, there are products that use wireless communication, and shield frames are usually designed on the circuit board to isolate electromagnetic interference (EMI). However, to make the shield frame fun
阅读全文