Intelligent Inspection Method of Circuit Board

 In the PCB industry, manufacturers have many methods for PCB inspection. For example: signal injection method, substitution method, offline Inspection, online inspection, parameter test method, waveform observation method, visual inspection method, signal tracking method, AC short circuit method, separation test method, etc.

The intelligent detection method of the circuit board needs to select the online test method according to the specific characteristics of the PCB board, in order to combine one or more processes, complement each other, and make comprehensive utilization.


First, use the idea of virtual instruments on the PCB to establish related application software, that is, implement various functions of traditional instruments through software, including oscilloscopes, signal generators, and various mathematical processes on the collected data. During the test, the digital signal is given by the test software.



Then, the PCB test system will have new design ideas. Adopt the design idea of automatic test system and virtual instrument based on USB bus to give full play to the role of computer. Try to replace the traditional instrument with a computer to reduce the volume of the instrument itself, reduce development costs, and improve development efficiency.



Next, after the D/A conversion, the analog excitation signal required for the test is applied to the test system, and then the test circuit is sent to the switch matrix through the test bus. When the switch matrix is connected to the switch matrix, it is controlled by the microprocessor to turn on and off. The tested PCB board is fixed on the needle bed, and the signal is applied to the corresponding position of the printed circuit board. The signal is pressed to the corresponding position on the printed circuit board, and its response is measured by the test circuit. Then the collected analog quantity is sent to the core controller, and the corresponding digital quantity is obtained through A/D conversion, and then fed back by the software on the PCB machine and processed by the PCB machine to determine whether the PCB board is qualified.



This online testing technology breaks through the previous method of inspecting circuit boards with the naked eye. The online testing technology has high efficiency and low missed detection rate, which realizes the automation of the detection field. The detection system adopts the idea of combining with virtual instruments, which reduces the hardware design and reduces the cost of the entire system.



SHENZHEN HOYOGO ELECTRONIC TECHNOLOGY CO., LTD. is an international, professional, reliable PCB manufacturer. We have 2 production bases with a monthly production capacity of 500,000 square meters. One-stop PCB product supply and solution. And HOYOGO have a management team with 25 years of average industry experience and reliable quality assurance.

评论

发表评论

此博客中的热门博文

What are the Advantages and Disadvantages of the OSP Technology

图片
     With the continuous development of the electronics industry, there are more and more PCB surface treatment technologies, and each technology has its own merits. OSP is a commonly used surface treatment technology process, what are its advantages and disadvantages?       Compared with other surface treatment technologies, OSP is somewhat different.  It uses a chemical method to produce an organic film on the clean bare copper surface, which acts as a barrier between the copper and the air.   OSP is organic, not  metallic,   and its cost is lower than most surface treatment technologies.     Advantages: With this organic film, it can resist the attack of moisture in the air without being oxidized before welding,  can withstand the test of high temperature, maintain good activity, and has a good tinning ability.  This layer of organic film will not cause damage to the sheet material. It can be easily removed by the solder resist during soldering. It can solder the copper wire and the
阅读全文

What PCBA Problems Can AOI Inspect

图片
        With the development of science and technology, the volume of PCBA is getting smaller and more precise, and some defects in processing cannot be distinguished with the naked eye, so AOI has appeared.  So what PCBA problems can AOI inspect?   The working principle of AOI is to first collect and input parameters such as images, component positions, solder joints and other parameters of the good-quality board.   During the inspection, the instrument automatically scans the circuit board and automatically captures the image, and then compares the collected data with the pre-entered parameters to determine whether the characteristics of solder joints, components and other aspects are consistent. If the data is inconsistent, the d efect  will be flagged through the display for maintenance personnel to repair.     AOI is mainly used to inspect solder paste printing, component placement and soldering. For example: too much or too little solder paste,   solder paste printing offset;  co
阅读全文

The Role of Shield Cover in PCB Design

图片
  SHENZHEN HOYOGO ELECTRONIC TECHNOLOGY CO., LTD. specializes in providing overall PCBA electronics manufacturing services, and can also provide customers with a full range of value-added services: including SMT assembly, PCB program development, schematic design, PCB layout and routing, Bom list matching, component procurement and other services. Do you know the role of shield cover in PCB design? What is a Shield Cover? The shield cover is an alloy metal cover, which is a vital component to reduce the radiation of the display. It is used in MID or VR products, which can effectively reduce the mutual interference between modules. It is common in the isolation between the main control function module and the power module and the Wifi module. The  P urpose of  S hield  Cover   C lip Generally, there are products that use wireless communication, and shield frames are usually designed on the circuit board to isolate electromagnetic interference (EMI). However, to make the shield frame fun
阅读全文