Six Rework and Repair Skills for Bad SMT

 Usually, after reflow soldering, the yield rate of PCB cannot reach 100%, and some defects will appear more or less. Among these defects, some are surface defects, which only affect the surface appearance of solder joints, but do not affect the function and life of the product. However, some defects will seriously affect the function and life of the product, such as: misalignment, bridge connection, etc. Such defects must be reworked and repaired. Do you know any skills for reworking and repairing bad SMT?

 

 

 

1. Manual rework and repair and soldering should follow the principle of SMT components first small and then large, first low and then high. First solder chip resistors, chip capacitors, transistors, then solder small IC devices, large IC devices, and finally solder plug-ins.

 

 

2. When soldering chip components, the width of the soldering bit should be consistent with the width of the components. If it is too small, it will not be easy to position when soldering.

 

 

3. When soldering SOP, QFP, PLCC and other devices with pins on two or four sides, several positioning points should be soldered on both sides or four sides first. After careful inspection to confirm that each pin matches the corresponding pad, drag soldering is performed to complete the soldering of the remaining pins.

 

 

4. The speed should not be too fast when dragging soldering, just drag 1-2 solder joints in about 1s or so.

 

 

5. After soldering, use a magnifying glass of 4 to 6 times to check whether there is any bridge between the solder joints, and the soldering of the same part shall not exceed twice in a row. If it is not welded well once, it should be cooled before soldering to prevent the pad from falling off.

 

 

6. When soldering IC devices, evenly apply a layer of solder paste on the pad, which can not only infiltrate and flux the solder joints, but also improve maintenance efficiency.

 

 

SHENZHEN HOYOGO ELECTRONIC TECHNOLOGY CO., LTD. is a company that specializes in providing overall PCBA electronics manufacturing services, including one-stop services from upstream electronic component procurement to PCB production and processing, SMT, DIP plug-in, PCBA testing, and finished product assembly.


评论

发表评论

此博客中的热门博文

What are the Advantages and Disadvantages of the OSP Technology

图片
     With the continuous development of the electronics industry, there are more and more PCB surface treatment technologies, and each technology has its own merits. OSP is a commonly used surface treatment technology process, what are its advantages and disadvantages?       Compared with other surface treatment technologies, OSP is somewhat different.  It uses a chemical method to produce an organic film on the clean bare copper surface, which acts as a barrier between the copper and the air.   OSP is organic, not  metallic,   and its cost is lower than most surface treatment technologies.     Advantages: With this organic film, it can resist the attack of moisture in the air without being oxidized before welding,  can withstand the test of high temperature, maintain good activity, and has a good tinning ability.  This layer of organic film will not cause damage to the sheet material. It can be easily removed by the solder resist during soldering. It can solder the copper wire and the
阅读全文

What PCBA Problems Can AOI Inspect

图片
        With the development of science and technology, the volume of PCBA is getting smaller and more precise, and some defects in processing cannot be distinguished with the naked eye, so AOI has appeared.  So what PCBA problems can AOI inspect?   The working principle of AOI is to first collect and input parameters such as images, component positions, solder joints and other parameters of the good-quality board.   During the inspection, the instrument automatically scans the circuit board and automatically captures the image, and then compares the collected data with the pre-entered parameters to determine whether the characteristics of solder joints, components and other aspects are consistent. If the data is inconsistent, the d efect  will be flagged through the display for maintenance personnel to repair.     AOI is mainly used to inspect solder paste printing, component placement and soldering. For example: too much or too little solder paste,   solder paste printing offset;  co
阅读全文

The Role of Shield Cover in PCB Design

图片
  SHENZHEN HOYOGO ELECTRONIC TECHNOLOGY CO., LTD. specializes in providing overall PCBA electronics manufacturing services, and can also provide customers with a full range of value-added services: including SMT assembly, PCB program development, schematic design, PCB layout and routing, Bom list matching, component procurement and other services. Do you know the role of shield cover in PCB design? What is a Shield Cover? The shield cover is an alloy metal cover, which is a vital component to reduce the radiation of the display. It is used in MID or VR products, which can effectively reduce the mutual interference between modules. It is common in the isolation between the main control function module and the power module and the Wifi module. The  P urpose of  S hield  Cover   C lip Generally, there are products that use wireless communication, and shield frames are usually designed on the circuit board to isolate electromagnetic interference (EMI). However, to make the shield frame fun
阅读全文